Mazda 13B-MSP Installationshandbuch

Stöbern Sie online oder laden Sie Installationshandbuch nach Motor Mazda 13B-MSP herunter. Mazda 13B-MSP Installation manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 18
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet4.8 / 5. Basierend auf22 Kundenbewertungen
Seitenansicht 0
GReddy Turbo Kit
2003 Mazda RX-8 (13B-MSP)
T618Z 10cm
2
(Actuator Type)
Emanage Ultimate
Seitenansicht 0
1 2 3 4 5 6 ... 17 18

Inhaltsverzeichnis

Seite 1

GReddy Turbo Kit 2003 Mazda RX-8 (13B-MSP) T618Z 10cm2 (Actuator Type) Emanage Ultimate

Seite 2

3-3 Oil Pressure Line Installation 1. Remove the factory oil pressure switch at the left side of the rear rotor housing and install the Oil pressure

Seite 3 - Installation Manual

5. Connect the oil pressure line that was installed in the step 3-2 to the turbocharger. Install the turbocharger to the manifold using the provided

Seite 4 - 1. Parts List

3-5 Intercooler Installation 1. Remove the auxiliary temp sensor on the bumper reinforcement, and rotate it 180°, then reinstall it back to the origi

Seite 5

6. Secure C-5 bracket to the speed sensor harness bracket (LH). (Parts Used #11, 12, 13, 34, 35, 37, 41, 42, 56) 7. Reinstall the front stabili

Seite 6 - Part List

4. Assemble the Airinx back together and hand tight the top screw. 5. Remove the factory Airflow meter off from the air cleaner box and install the

Seite 7 - 57 58 59 60 61

2. Install the O2 sensor to the down pipe adapter and install the adapter to the Turbo using provided gasket and hardware. Connect the O2 sensor co

Seite 8 - 2. Factory Parts Removal

3-8 e-manage Ultimate installation and vacuum hose connection for the actuator. 1. Remove the washer tank and drill a 1" hole on the fire wall.

Seite 9 - 3. Turbo Kit Installation

3-9 Bumper installation 1. Cut the under cover and the inner fender cover to clear the compression pipe. 2. Reinstall the front bumper.

Seite 10

Starting the Engine 1. Reinstall the battery tray, battery box, battery, and connect the positive terminal only. 2. Reinstall the front strut tower

Seite 12

2003 Mazda RX-8 (13B-MSP)T618Z 10cm2 (Actuator Type) Installation Manual Please read the entire manual before installing this kit. Application:

Seite 13

1. Parts List 1. Turbocharger T618Z 10cm2 P380 1 2. Exhaust Manifold Ductile Iron Cast 1 3. Downpipe Adapter

Seite 14 - Airflow

36. Silicone Hose 50∅ - 60∅ Reducer 1 37. “ 80∅ x 80∅ Reducer 1 38. “ 80∅ - 90∅ Reducer

Seite 15

Part List 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24~26 27

Seite 16 - Orifice Fitting

28 29 30~32 33~35 36~38 39~43 44 45 46 47 48 49 50, 51 52, 53 54~56 57 58 59 60 61

Seite 17

2. Factory Parts Removal When removing the stock parts, please refer to the factory RX8 Workshop manual for proper procedures. 2-1 Factory Parts Re

Seite 18

3. Turbo Kit Installation 3-1 Intake Manifold Plate Installation 1. Remove the extension manifold (upper). Please refer to RX8 worksho

Kommentare zu diesen Handbüchern

Keine Kommentare