Mazda GENUINE C930 V7 620 Bedienerhandbuch PDF herunterladen

GENUINE Remote engine start

INSTALLATION INSTRUCTIONS



Thank you for purchasing a genuine Mazda accessory.

Before removal and installation, be sure to thoroughly read these instructions.

Please read the contents of this booklet in order to properly install and use the Remote engine

start. Your safety depends on it.

Keep these instructions with your vehicle records for future reference.



x There are several WARNING and CAUTION sections in this booklet concerning safely when

installing or removing the Remote engine start. Always read and follow them in order to prevent injuries,

accidents, and possible damage to the vehicle.

WARNING: Indicates a situation in which serious injury or death could result if the warning

is ignored.

CAUTION: Indicates a situation in which bodily injury or damage to the vehicle could result if the

caution is ignored.

x For areas indicating the tightening torque in this instruction manual, tighten to the specified torque using

a torque wrench. For areas in which the tightening torque is indicated inside parentheses ( ), the

tightening torque is indicated as a reference value, however tightening using a torque wrench is not

necessary.

x Do not modify the Remote engine start.

x Do not install the Remote engine start in any way other than described in the following instructions.

x If in any doubt, please ask your Mazda dealer to install the accessory in order to prevent errors in

installation.

x If you have any questions about the use of the accessory, ask your Mazda dealer for proper advice

before using it.

x Mazda and its suppliers are not responsible for injuries, accidents, and damage to persons and property

that arise from the failure of the dealer or installer to follow these instructions.

x To ensure safety and reliability of the work, installation, removal and disposal work must carried out by

an Authorized Mazda Dealership.

x Be careful not to lose removed parts, and be sure that they are kept free from scratches, grease or

other dirt.

PART NAME: Remote engine start

VEHICLE: MAZDA CX-5

PART NUMBER: C930 V7 620 (CONTOROLLER KIT)

KD33 V7 630 (HARNESS KIT)

䌛

KD53 V7 629 (Hood Switch)

䌝

To the dealer

x Please turn over these instructions to the customer after installation.

To the customer

x Keep these instructions after installation. The instructions may be necessary

for installing other optional parts or removal of this accessory.

x Should the vehicle or this accessory be resold, always leave these instructions

with it for the next owner.

x When the remote engine start is removed, clear the remote engine start

information programmed to the vehicle by following the clearing procedure for

the advanced key in the workshop manual. In addition, after clearing, the

advanced key has to be programmed again.

WARNING

NOTE

1 2 3 4 5 6 ... 17 18

Inhaltsverzeichnis

Seite 1 - GENUINE Remote engine start

GENUINE Remote engine start INSTALLATION INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure

Seite 2 - 1. PARTS

1. Install the hood switch to the hood latch and secure it using a screw (1 location). 2. Hook the hood switch harness to the hood

Seite 3 - ٕParts list

6. Install a tie wrap (Black) to the mount bases and tighten the hood switch harness at one location.  7. Peel back the tape backing on the back

Seite 4 -  REQUIRED TOOLS

11. Insert the hood switch harness (Red) terminal to the empty terminal of the vehicle wiring harness 18 pin connector (terminal N).

Seite 5 - CONNECTION DIAGRAM

13. Branch connect the hood switch harness (Black) to the vehicle wiring harness 12 pin connector (terminal A (Black)) using an electro tap, and wra

Seite 6 - Insert to empty terminal㩷

1. Wrap urethane tape around the RES ECU. 2. Degrease the RES ECU using primer, and affix double-sided adhesive tape. 3. Degreas

Seite 7 - PART REMOVAL

4. Connect the TEMP sensor to the harness 2 pin connector. 5. Wrap remaining urethan tape in Step1 to the harness and the TEMP sensor. 6. Sec

Seite 8

10. Route the harness and secure it to the dashboard member using tie wraps (White) at two locations. 11. Connect the harness 12 pin con

Seite 9 - Glove compartment

1. After verifying the harness routing, connect the negative battery cable. 2. Register the controller (= RES ECU) with

Seite 10 - 6. HOOD SWITCH INSTALLATION

㩷MAZDACX-5 Remote engine start C930 V7 620 (CONTOROLLER KIT) KD33 V7 630 (HARNESS KIT) KD53 V7 629 (HOOD SWITCH)̪ A. Vehicle parts reinstallation x

Seite 11

ٕInstallation view1. PARTS (Sold separately) Hood switch (Only for vehicle without theft-deterrent system) RES ECU Harness Ha

Seite 12

ٕParts list z CONTOROLLER KIT (Part No. C930 V7 620)㩷Part㩷 Part name㩷 Qty.㩷 Part㩷 Part name㩷 Qty. Part㩷 Part name㩷 Qty. Remote Start Transmitter

Seite 13

 REQUIRED TOOLSڏScrewdriver (Flathead)ڏScrewdriver (Phillips) ڏSocket wrenchڏFastener removerڏNipper ڏPliers㩷㩷㩷ڏMasking tape ڏElectr

Seite 14

 4䋮CONNECTION DIAGRAM

Seite 15

Figure shows connector viewed from harness side. TYPE B TYPE AInsert to empty terminal㩷㩷 (TYPE A and B)

Seite 16

 Negative battery cable disconnection 1. Set the selector lever to P range. 2. Disconnect the negative battery cable and wrap tape around

Seite 17 - OPERATION CHEC

Ԛ Main fuse cover removal 1. Detach the main fuse cover tab (1 location), and lift the rear part of the main fuse cover to remove it.  ԛ Fas

Seite 18 - Remote engine start

2. Pull the stay damper in the direction of the arrow shown in the figure and remove the hook B. 3. Pull the glove compartment in the di

Weitere Dokumente für Kfz-Elektronik Mazda GENUINE C930 V7 620

Um das Dokument anzuzeigen Mazda GENUINE C930 V7 620 Bedienerhandbuch

Mazda GENUINE C930 V7 620 Bedienerhandbuch (33 Seiten)

Um das Dokument anzuzeigen Mazda GENUINE C930 V7 620 Bedienungsanleitung

Mazda GENUINE C930 V7 620 Bedienungsanleitung (22 Seiten)

Mazda GENUINE C930 V7 620 Bedienerhandbuch (19 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Mazda GENUINE C930 V7 620 Bedienerhandbuch

Stöbern Sie online oder laden Sie Bedienerhandbuch nach Kfz-Elektronik Mazda GENUINE C930 V7 620 herunter. Mazda GENUINE C930 V7 620 Instruction manual Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Kfz-Elektronik Mazda GENUINE C930 V7 620

Kommentare zu diesen Handbüchern