Mazda LF Spezifikationen Seite 5

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 60
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 4
GENERAL INFORMATION
00–00–3
00–00
Repair procedure
1. Most repair operations begin with an overview illustration. It identifies the components, shows how the parts fit
together, and describes visual part inspection. However, only removal/installation procedures that need to be
performed methodically have written instructions.
2. Expendable parts, tightening torques, and symbols for oil, grease, and sealant are shown in the overview
illustration. In addition, symbols indicating parts requiring the use of special service tools or equivalent are also
shown.
3. Procedure steps are numbered and the part that is the main point of that procedure is shown in the illustration
with the corresponding number. Occasionally, there are important points or additional information concerning a
procedure. Refer to this information when servicing the related part.
GREASE
GREASE
GREASE
GREASE
SHOWS NON-REUSEABLE PARTS
SHOWS DETAILS
KNUCKLE
UPPER TRAILING LINK
LOWER TRAILING LINK
SST
SST
SST
SST
R
R
R
R
9
2
1
4
5
3
6
1
2
8
7
12
10
11
N·m {kgf·m, ft·lbf}
118—156 {12.0—16.0, 87—115}
94—116 {9.5—11.9, 69—86}
43—56 {4.3—5.8, 32—41}
49 T028 304
49 T028 305
49 T028 303
Procedure
LOWER TRAILING LINK, UPPER TRAILING LINK REMOVAL/INSTALLATION
1. Jack up the rear of the vehicle and support it with safety stands.
2. Remove the undercover. (See 01-10-4 Undercover Removal)
3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.
5. Inspect the rear wheel alignment and adjust it if necessary.
1
Split pin
2
Nut
3
Lower trailing link ball joint
4
(See 02-14-5 Lower Trailing Link Ball Joint Removal Note)
Bolt
5
Lower trailing link
6
Dust boot (lower trailing link)
7
Split pin
8 Nut
9 Upper trailing link ball joint
(See 02-14-5 Upper Trailing Link Ball Joint Removal Note)
10
Nut
11
Upper trailing link
12
Dust boot (upper trailing link)
Lower Trailing Link Ball Joint, Upper Trailing Link
Ball Joint Removal Note
Remove the ball joint using the SSTs.
44—60 {4.4—6.2, 32—44}
"Removal/Installation"
Portion
"Inspection After
Installation" Portion
INSTALL THE PARTS BY
PERFORMING STEPS
13 IN REVERSE ORDER
SHOWS PROCEDURE ORDER
FOR SERVICE
SHOWS TIGHTENING
TORQUE
SPECIFICATIONS
SHOWS SERVICE
ITEM (S)
INDICATES ANY RELEVANT
REFERENCES WHICH NEED
TO BE FOLLOWED DURING
INSTALLATION
SHOWS SPECIAL
SERVICE TOOL (SST)
FOR SERVICE OPERATION
SHOWS APPLICATION
POINTS OF GREASE, ETC.
SHOWS TIGHTENING
TORQUE UNITS
SHOWS SPECIAL
SERVICE TOOL (SST)
NO.
SHOWS REFERRAL
NOTES FOR
SERVICE
SHOWS THERE
ARE REFERRAL
NOTES FOR SERVICE
BHE0000W104
Seitenansicht 4
1 2 3 4 5 6 7 8 9 10 ... 59 60

Kommentare zu diesen Handbüchern

Keine Kommentare