MA2 MA000 Mazda ReferenceSubject: Drive cycle for 1996–2005 cars and B-Series trucksSource: Mazda service manualsThe purpose of the OBD-II Drive Cycle
MA11Mazda ReferenceMA000Figure MA000-15 5. Stop the vehicle and access the OBD-II Readiness Monitor with the scan tool to inspect the completion statu
MA12Mazda ReferenceMA000Figure MA000-16 NOTE:i All parameters must be within specification before the engine is started in order to initiate the EVAP
MA13Mazda ReferenceMA0004. Start the engine and let it run at idle for at least 10 seconds, then switch the ignition off5. Allow the vehicle to sit as
MA14Mazda ReferenceMA0004. Stop vehicle and access the OBD-II Readiness Monitor with the scan tool to inspect the completion status.5. Verify no DTCs
MA15Mazda ReferenceMA000z To perform this Mode 3 HO2S and catalyst drive cycle:1. Verify the following conditions are met:– The IAT sensor must be bel
MA16Mazda ReferenceMA000– The drive mode conditions must be met within 4 to 10 minutes after start up. If the time exceeds 10 minutes, switch the igni
MA17Mazda ReferenceMA0001996–2005 B-Series Trucks (All), 2001–05 Tributez To prepare the vehicle:1. Connect the scan tool and access the fuel level in
MA18Mazda ReferenceMA0003. From a stop, accelerate to 65 mph (104 kph). Decelerate at closed throttle until 40 mph (64 kph) without applying the brake
MA19Mazda ReferenceMA000NOTE:i To initiate the EVAP monitor, the EVAPPDC parameter must increase to at least 75% (canister purge vent open). At this t
MA20Mazda ReferenceMA000EGR System Repair Verification Drive ModeThis mode applies to the following models:• 2003 Mazda 6z To perform this drive cycle
MA3Mazda ReferenceMA000MODE 1—Adaptive Memory Produce Drive ModeThis mode applies to the following models:• 1996–97 626 /MX6 with 2.5L engine• 1996–97
MA21Mazda ReferenceMA000– If RFCFLAG reads “yes”, start the engine and warm it up completely.2. Verify all electrical accessory loads (headlights, blo
MA22Mazda ReferenceMA0007. Stop the vehicle and switch the ignition off.8. Allow the vehicle to sit as is for at least 10 minutes.9. Start the engine.
MA23Mazda ReferenceMA000• The OBD-II system detects malfunction.• The Drive Mode procedure is not completed correctly.• Disconnecting the battery will
MA24Mazda ReferenceMA0003. Drive vehicle as shown in Figure MA000-24. Figure MA000-24 4. Stop the vehicle and access ON BOARD SYSTEM READINESS to veri
MA25Mazda ReferenceMA000 Figure MA000-25 NOTE:i . Driving conditions before driving at constant speed are not specified4. Stop the vehicle and access
MA26Mazda ReferenceMA0007. Stop vehicle and turn key off.8. Leave vehicle as it is for 10 minutes or more.9. Start the engine.10. Access ON BOARD SYST
MA27Mazda ReferenceMA000Figure MA000-26 6. Turn key off.7. Access ON BOARD SYSTEM READINESS to verify OBD monitoring status.– If completed, all OBD mo
MA28Mazda ReferenceMA000• PCM Adaptive Memory Produce Drive Mode• EGR System Repair Verification Drive Mode• HO2S heater, HO2S, and TWC Repair Verific
MA29Mazda ReferenceMA000Mode 2 (EGR System Repair Verification Drive Mode)z To perform this drive mode:1. Perform “PCM Adaptive Memory Produce Drive M
MA30Mazda ReferenceMA000Figure MA000-28 NOTE:i Driving condition before driving at constant speed is not specified.4. Stop vehicle and access ON BOARD
MA4Mazda ReferenceMA000Figure MA000-2 Figure MA000-3 Figure MA000-4
MA31Mazda ReferenceMA0005. Start the engine and idle it for 15 minutes or more.6. Drive the vehicle at 40 to 50 mph (65 to 80 kph) for 5 minutes or mo
MA32Mazda ReferenceMA000Figure MA000-29 6. Turn key off and leave vehicle for 10 minutes or more with key off.7. Start and stop engine.8. Access ON BO
MA33Mazda ReferenceMA000• For Specific Drive Mode, specified drive modes have been set for each individual monitoring item requested by OBD-II regulat
MA34Mazda ReferenceMA000PCM Adaptive Memory Production Drive Modez To perform this drive mode:1. Start the engine and warm completely.2. Verify follow
MA35Mazda ReferenceMA000Figure MA000-32 4. Stop the vehicle and access ON BOARD SYSTEM verify OBD monitoring status:– If completed, the OBD monitoring
MA36Mazda ReferenceMA000Figure MA000-33 EVAP System Repair Verification Drive ModeNOTE:i If “EVAP System Repair Verification Drive Mode” cannot be per
MA37Mazda ReferenceMA000PCM Adaptive Memory Production, EGR, HO2S heater, HO2S, TWC, and EVAP System Repair Verification Drive Modez To perform this d
MA38Mazda ReferenceMA0006. Turn key off.7. Access ON BOARD SYSTEM READINESS to verify OBD monitoring status:– If completed, OBD monitoring status item
MA39Mazda ReferenceMA000IMPORTANT:While performing the Drive Mode, always operate the vehicle in a safe and lawful manner.When observing monitor syste
MA40Mazda ReferenceMA000Figure MA000-35 5. Access DIAGNOSTIC MONITORING TEST RESULTS to verify monitoring results:– If detected values not within spec
MA5Mazda ReferenceMA000Figure MA000-5 Figure MA000-6 Figure MA000-7
MA41Mazda ReferenceMA0004. Stop the vehicle and access ON BOARD SYSTEM READINESS to verify monitor status:– If completed, OBD monitoring status items
MA42Mazda ReferenceMA0003. Verify following conditions and correct if necessary:– All accessory loads (A/C, headlights, blower fan, rear window defros
MA43Mazda ReferenceMA0007. Access ON BOARD SYSTEM READINESS menu of GENERIC OBD-II FUNCTION to verify the OBD monitoring status:– If completed, all of
MA44Mazda ReferenceMA000• Do not disconnect the battery after Drive Mode, this will reset PCM memory.• The scan tool can be used at anytime through th
MA45Mazda ReferenceMA000Figure MA000-39 4. Stop the vehicle and access ON BOARD SYSTEM READINESS menu to inspect OBD monitoring status:– If completed,
MA46Mazda ReferenceMA000NOTE:i Driving conditions before driving at constant speed are not specified.4. Stop the vehicle and access ON BOARD SYSTEM RE
MA47Mazda ReferenceMA000Single Drive Mode (PCM Adaptive Memory Production, EGR System, HO2S Heater, HO2S, TWC, and EVAP System Verification)z To perfo
MA48Mazda ReferenceMA0006. Turn key off.7. Access ON BOARD SYSTEM READINESS to inspect the monitor status:– If completed, all OBD monitoring status it
MA49Mazda ReferenceMA000Mode 1 (PCM Adaptive Memory Produce Drive Mode)z To perform this drive mode:1. Start the engine and warm completely.2. Verify
MA50Mazda ReferenceMA0006. Verify no DTCs set.Mode 6 (EVAP System Repair Verification Drive Mode)NOTE:i If the Mode 6 cannot be performed (you cannot
MA6Mazda ReferenceMA000Figure MA000-8 MODE 2—EGR System Repair Verification Drive ModeThis mode applies to the following models:• 1996–97 626/MX6 with
MA7Mazda ReferenceMA0005. Stop the vehicle and access the OBD-II Readiness Monitors with the scan tool to inspect the completion status. If not comple
MA8Mazda ReferenceMA000• 1999–2003 Protege• 2000–03 MPVz To perform this Mode 3 O2S and catalyst drive cycle:1. Verify that all electrical loads (head
MA9Mazda ReferenceMA000MODE 3—EVAP System Repair Verification Drive ModeThis mode applies to the following models:• 1996–98 MPV with 3.0L enginez To p
MA10Mazda ReferenceMA000z To perform this Mode 4 EVAP drive cycle:1. Verify that all electrical loads (headlights, blower, rear window defroster, and
Kommentare zu diesen Handbüchern